Firequip - Booster Hose

Firequip - Booster


DESCRIPTION

Fire hose is one of the most important tools used by the fire department. As such, the following specification must be strictly adhered to unless the proposed specification exceeds specification listed. Only the fire department can determine if a proposed product meets and exceeds these specifications “The Quick One The hose that must be relied upon for fast and reliable fire attack – before the small localized fire can grow out of control. Firefighters demand performance – the first time and every time.” Pressure Contraction and Elongation – When pressurized, a poorly constructed hose may contract or elongate. This can endanger a firefighter in a high place or in a tight spot. It can also damage equipment such as hose reels which can actually be crushed. FireQuip Booster Hose is made with precision reinforcement angles to control length change under pressure to avoid these problems. Durable, Bright Red Cover – It looks good and lasts longer for overall better cost effectiveness and reliability. The cover shall be EPDM rubber, which resists abrasion, gouging, ultra-violet, ozone aging and heat. Long Lengths – Firequip Fire Engine Booster Hose is produced in continuous lengths of 200 feet for 1 inch hose and 300 feet for ¾ inch. This reduces the number of coupling connectors required, reducing cost and increasing hose integrity. Full 4:1 Safety Factor – You must require a 4:1 safety factor for your booster hose to insure safety and reliability. This means 800 Booster Hose must be rated for 3200 minimum burst pressure. A lesser grade hose cannot be relied upon to handle pressure surges, end pull, kinking and other abuse, coupling retention and aging. Meets UL 92 Design and Performance Criteria – Firequip Fire Engine Booster Hose meets or exceeds the requirements listed in UL 92 specification for 800 PSI Booster Hose. The manufacturer shall be ISO 9001-2008 Quality Certified.

TECHNICAL INFORMATION APPLICABLE SPECIFICATIONS: Unless otherwise specifically designated in this specification, all measurements and test necessary to determine compliance of the hose with the specified requirements shall be made in accordance with Standard Specifications for Testing Rubber Hose, AZTM, D-380-81.

TYPES AND SIZES: The type of yarn shall be four spirals of continuous high tensile aramid yarn. The hose size shall be 1 inch or 3/4 inch nominal internal diameter.

MATERIAL AND WORKMANSHIP: All materials used in the fabrication of the hose shall be of the best quality normally used for the purpose in good commercial practice for the type designated. The workmanship shall be of the highest quality.

TUBE CONSTRUCTION DETAIL: The liner tube shall be of smooth black synthetic EPDM rubber. The tube shall be extruded of uniform thickness throughout its length, the waterway of the tube shall be smooth and free from imperfections. The thickness of the tube shall be not less than .060 inches. The adhesion between the layer and reinforcement between tube and reinforcement, or between the cover and reinforcement shall be such that a weight of 10 pounds suspended from a ring specimen 1” wide will cause separation at a rate not greater than 1 inch per minute. When tested within 50 days from date shipment is received, a section of the liner tube shall comply with the following requirements. The test specimen shall be cut along the hose axis. Tensile strength, minimum ————————————1000 PSI Elongation, minimum ———————————————-250% Accelerated Air-Oven Aging (70 hours at 212 degrees Fahrenheit) Maximum Tensile Loss—————————–20% Maximum Elongation Loss ———————–20%

REINFORCEMENT DETAIL: Reinforcement shall consist of multiple plies of high tensile Aramid yarn. The reinforcement shall be evenly applied, free from defects in material and workmanship that are unsightly or may affect the serviceability of the finished hose.

FINISHED HOSE: The internal diameter of 1” hose shall be 1 inch ± 3/64” and ¾” hose shall be ¾” ± 3/64”. The outside diameter of the hose shall be 1.5 inches ± 1/16” and ¾” hose shall be 1-3/16”. Each piece of hose of nominal 50 foot length shall be supplied in such additional length as will permit the attachment of coupling fittings and still provide a minimum of 50 feet of hose, from back of couplings, when measured under 10 PSI water pressure. The weight of 50 feet of 1” hose, untreated, without couplings is approximately 30 pounds. The weight of a 100 foot hose without couplings is about 60 lbs, and 50 ft of ¾” hose is 19 lbs. and 100 ft is 37 lbs. An 18 inch length, while lying flat and straight shall not burst under 3200 PSI. Each length of hose shall withstand hydraulic test pressure of not less than 1600 PSI for one minute. The elongation between 10 and 800 PSI shall not exceed 6%. Twist of the hose in direction to loosen couplings, between 10 and 800 PSI shall not exceed 7° per foot.

COUPLINGS: Barway couplings or permanent crimped swage couplings can be used.

WARRANTY: The manufacturer warrants the hose to be free from defects in materials and workmanship for a period of five years. This warranty shall provide for the repair or replacement of hose and couplings proven to have failed due to faulty material or workmanship.

Download Data Sheet >








Fire Apparatus Sales & Service
Phone: 814.472.8650
Fax:  814.472.4520
Ebensburg, PA  15931

Kaza Fire Trucks  A Division of Kaza Fire Equipment, LLC.   814-472-8650  | Fax:  814-472-4520 | info@kazafiretrucks.com

Website Created By:  AllYouWantWebs.com |  ©2019, All Rights Reserved.